Skip to product information
1 of 1

Flux Battery Hub

Manual 18650 Cylindrical Cell Crimping Machine

Manual 18650 Cylindrical Cell Crimping Machine

SKU:FL-CF650

  • Formal Quotes & POs
  • DDP to Most Destinations
  • Return Policy Available

This manual 18650 cylindrical cell crimper uses a hand-operated hydraulic mechanism to close compatible cylindrical battery cases in laboratory assembly and small-batch trials. The standard configuration includes one 18650 sealing die set and uses a two-step crimping process. A built-in pressure gauge and adjustable hydraulic relief valve support controlled setup for the selected case, cap and gasket.

Manual hydraulic 18650 cylindrical cell crimper with two-step sealing tooling and pressure gauge — representative illustration
Representative equipment illustration adapted from the product reference. Final tooling and configuration are confirmed in the quotation.

Key Features

  • Manual hydraulic drive with no electrical supply required.
  • Standard 18650 tooling for two-step cylindrical cell sealing.
  • Built-in gauge for observing hydraulic pressure during operation.
  • Internal relief valve with an adjustable pressure limit.
  • Compact steel-frame construction for benchtop use and suitably planned glovebox installations.
  • Other cylindrical-cell die configurations can be discussed against the case drawing.

Technical Specifications

Parameter Specification
Model / SKU FL-CF650
Drive Hand-operated hydraulic
Electrical supply Not required
Standard sealing die One 18650 cylindrical-cell die set
Sealing sequence Two-step crimping
Typical hydraulic gauge reference 80–100 kgf/cm²; factory-adjusted process reference
Maximum hydraulic gauge reference 200 kgf/cm²; adjustment above the factory setting requires technical confirmation
Maximum pressing load Approximately 8 metric ton-force at the stated maximum hydraulic setting
Hand-lever operating effort Specified below 6 kgf
Pressure protection Internal adjustable hydraulic relief valve
Frame material High-strength chromium steel with plated / coated surface treatment
External dimensions (L × W × H) 235 × 190 × 360 mm
Equipment weight 40 kg

Hydraulic gauge pressure is not pressure on the battery case. The 80–100 kgf/cm² reference is approximately 7.8–9.8 MPa in the hydraulic circuit, while 200 kgf/cm² is approximately 19.6 MPa. The approximately 8-ton figure describes maximum press capability, not a recommended crimping load for every shell. Contact FluxBatteryHub before changing the factory pressure limit or using settings above the normal process reference.

18650 Tooling and Two-Step Sealing

The standard package is configured for 18650 cells, with two forming stages performed using the corresponding tooling arrangement. Follow the approved tooling sequence and settings for the actual case, cap and gasket. Other cylindrical formats require confirmation of the suitable die and machine clearances; they are not automatically included or guaranteed compatible.

Send the case drawing, rim geometry, cap and gasket dimensions and desired finished closure for selection. Confirm any separate case-rim grooving required by the assembly procedure before sealing. This unit does not perform winding, tab welding, electrolyte filling, case grooving, disassembly or electrical cell testing.

Laboratory Setup and Seal Validation

For glovebox use, check transfer-port clearance, internal working space, manual-handle travel and safe handling of the 40 kg machine. Confirm hydraulic-fluid containment and compatibility with the controlled environment. Compact dimensions alone do not establish compatibility with every glovebox.

Establish the pressure and forming sequence using the selected shell assembly. Validate finished dimensions, gasket condition, leakage and electrical isolation against your acceptance criteria. Hydraulic operation and a relief valve do not by themselves guarantee a leak-free seal or eliminate short circuits. No throughput, leak-rate specification or certification is claimed without configuration-specific confirmation.

Operation and Care

Use trained personnel and keep hands clear of the dies and moving guides. Do not defeat the relief valve or exceed the approved die and machine ratings. Release hydraulic pressure fully before removing tooling or performing maintenance. Inspect the gauge, fluid level, fittings and fasteners, address any leakage, and keep forming surfaces clean using methods compatible with the cell components. Plan lifting and placement for the machine weight.

Related Cylindrical Cell Assembly Products

For upstream assembly, compare the battery electrode winding machine and cylindrical cell negative-tab bottom spot welder. Review 18650 stainless-steel case sets, with die compatibility confirmed for the selected components. Browse cylindrical cell preparation equipment to match each separate process step.

Request a Quote

Send your cell format, case and cap drawings, gasket specification, preferred tooling, assembly requirements, quantity and delivery destination. Include any glovebox clearance constraints. We will confirm the configured crimper and provide a written quotation.

View full details

Request a Lab Quote

For institutional purchase orders, non-standard configurations, larger quantities or written shipping terms, send the details below. We will reply before anything is ordered.

Product: Manual 18650 Cylindrical Cell Crimping Machine
SKU: FL-CF650

Submitting this form does not place an order or confirm availability, pricing or delivery. DDP shipping is included for most destinations we serve. Remote, restricted or unsupported destinations may require different terms, which we will confirm before fulfillment.