Skip to product information
1 of 1

Flux Battery Hub

Pouch Cell Hot Press and Short Circuit Tester

Pouch Cell Hot Press and Short Circuit Tester

SKU:FL-DRY200

  • Formal Quotes & POs
  • DDP to Most Destinations
  • Return Policy Available

This pouch cell hot press and short circuit tester combines heated flat pressing with insulation-resistance screening in one laboratory station. Pneumatic upper and lower platens apply adjustable heat and compression to shape cell cores and develop thickness consistency. The integrated electrical test provides a separate screening function for insulation defects during cell assembly research.

Pouch cell hot press and short circuit tester with heated platens, protective enclosure and light curtain — representative illustration
Representative equipment illustration adapted from the product reference. Dimensions and final controls vary with the selected configuration.

Compare Cell Capacity and Machine Size

Specification FL-DRY200 FL-DRY300 FL-DRY350
Maximum cell dimensions (L × W × H) 200 × 200 × 70 mm 300 × 300 × 70 mm 350 × 350 × 70 mm
Machine dimensions (L × W × H) 350 × 320 × 550 mm 450 × 420 × 650 mm 500 × 470 × 650 mm
Rated power 2 kW 3 kW 3 kW
Approximate equipment weight 180 kg 180 kg 180 kg

Choose a model against the full cell drawing, including tabs, fixtures and required clearances. Maximum cell dimensions do not specify platen dimensions or guarantee compatibility with every cell construction.

Select Model and Power Supply

Select one factory electrical version, then use Request a Quote. Both voltage options are available for each model.

Key Features

  • Single-station hot press shaping with adjustable temperature and pneumatic loading.
  • Digital display of temperature settings and operating values.
  • Manual and automatic test modes with automatic short-circuit alarm.
  • Integrated insulation-resistance and leakage-current measurement functions.
  • Light-curtain protection and protective enclosure around the moving press area.

Shared Technical Specifications

Parameter Specification
Heating range Ambient temperature to 130°C, adjustable
Temperature control reference ±4°C
Nominal pressing load range 0–900 kgf (approximately 0–8.83 kN)
Working travel 0–80 mm
Adjustable DC test voltage 0–500 V
Maximum measurable leakage current 50 µA
Maximum insulation-resistance measurement 199 MΩ
Short-circuit indication Automatic alarm
Test modes Manual and automatic
Compressed-air supply 0.5–0.8 MPa
Electrical supply AC 220V / 50Hz or AC 110V / 60Hz — select one factory version

The pressing-load figure is a force rating, not pressure per unit cell area. The temperature-control reference is not a verified temperature-uniformity specification over the full platen. The 50 µA value is the maximum measurable leakage current, not a universal pass/fail threshold. Test duration, contact arrangement, trip settings and calibration requirements must be confirmed for the configured system.

Hot Press Shaping and Insulation Screening

Use this equipment to develop flat-press shaping conditions for compatible pouch cell cores and to screen insulation using an approved test procedure. Set temperature, load, dwell and electrical test limits for the actual electrode stack, separator and assembly stage. Verify thickness and insulation results against your own acceptance criteria; pressing does not guarantee elimination of internal shorts.

This is not a charge/discharge formation cycler, a pouch-film heat sealer, or a destructive external short-circuit abuse-test system. An insulation test alone does not certify battery safety. Before applying a DC insulation test, confirm specimen condition and the test-contact arrangement; do not apply the high-voltage insulation output across a charged cell or assembled battery without an explicitly validated procedure and suitable protection.

Utilities and Operator Protection

Provide both compressed air and the selected electrical supply. The 110V / 60Hz and 220V / 50Hz versions are factory alternatives, not automatically switching dual-voltage input. Confirm nameplate current, plug and circuit requirements for the 2 or 3 kW model before installation.

Operate only with trained personnel, the enclosure and light curtain in place, and hands clear of hot platens and moving guides. Dual-button start is specified for FL-DRY300 and FL-DRY350; confirm the final control arrangement for FL-DRY200. Isolate electricity and compressed air, release stored pressure and allow the platens to cool before maintenance. Inspect guards and fasteners and keep the platen surfaces clean.

Related Pouch Cell Assembly Equipment

For upstream electrode assembly, compare the Z-fold electrode stacking machine and battery electrode winding machine. For a separate packaging step, see the pouch cell top and side heat sealer. Explore pouch cell preparation equipment to match each station to your process.

Request a Quote

Send your cell dimensions and assembly stage, required pressing conditions, insulation-test method, preferred model and electrical supply, quantity and delivery destination. We will confirm the suitable configuration and provide a written quotation.

View full details

Request a Lab Quote

For institutional purchase orders, non-standard configurations, larger quantities or written shipping terms, send the details below. We will reply before anything is ordered.

Product: Pouch Cell Hot Press and Short Circuit Tester
SKU: FL-DRY200

Submitting this form does not place an order or confirm availability, pricing or delivery. DDP shipping is included for most destinations we serve. Remote, restricted or unsupported destinations may require different terms, which we will confirm before fulfillment.