Skip to product information
1 of 1

Flux Battery Hub

Semi-Automatic Z-Fold Electrode Stacking Machine for Pouch Cells

Semi-Automatic Z-Fold Electrode Stacking Machine for Pouch Cells

SKU:FL-BDP200-B

  • Formal Quotes & POs
  • DDP to Most Destinations
  • Return Policy Available

This semi-automatic electrode stacking machine assembles cathode sheets, anode sheets and a continuous separator into a Z-fold stack for laboratory pouch cell development. Automatic separator tension control and cylinder-driven left/right separator movement assist the stacking process, with a foot switch for actuation. Its cantilevered benchtop layout supports sample preparation and small-batch process trials.

Semi-automatic Z-fold electrode stacking machine with separator feed rollers and benchtop stacking platform

Z-Fold Stacking for Pouch Cell Research

  • Continuous separator folding between alternating cathode and anode sheets.
  • Automatic separator tension control during delivery.
  • Foot-switch-controlled cylinder movement.
  • Automatic counting, zero reset and a digital timer.
  • Last-used parameter retention after power-off.
  • Benchtop configuration with a cantilevered working area.

Technical Specifications

Model / SKU FL-BDP200-B
Stacking method Z-fold separator stacking with cathode and anode sheets
Stack alignment Better than ±0.5 mm
Minimum stacking size 44 × 44 mm, including tab length; smaller sizes require replacement hold-down plates
Maximum stacking size 200 × 150 mm, including tab length; tabs on the long side
Maximum stack thickness 12 mm; thicker stacks require a different adjustment plate
Maximum separator roll diameter 220 mm
Separator delivery Automatic tension control; cylinder-driven left/right motion
Operator control Foot switch for cylinder actuation
Counter functions Automatic counting and zero reset
Other controls Digital timer; retention of last-used parameter settings after power-off
Power supply Single-phase AC 220V / 50Hz or AC 110V / 60Hz — select one factory version
Rated electrical power 200 W
Compressed-air pressure 0.4–0.6 MPa
Installation dimensions (L × W × H) 512 × 820 × 580 mm
Machine weight Approximately 50 kg
Recommended operating environment 25 ±3°C; 30–90% RH; away from vibration and electromagnetic interference

The stacking-size limits include tab length. Confirm the complete electrode outline and long-side tab position before selection. The standard configuration supports stacks up to 12 mm thick; smaller electrode sizes or thicker stacks require a tooling/configuration change and are not included as standard capability.

Alignment depends on electrode flatness, dimensions, separator properties, tension settings and operator technique. Confirm the measurement method and acceptance criteria with representative materials. The two power supplies are factory alternatives, not an automatic dual-voltage input. Electrical power and compressed air are both required.

Configuration and Material Selection

Provide cathode and anode drawings, tab geometry, separator width and thickness, roll dimensions, intended layer count and target stack thickness. Confirm separator roll-core compatibility and hold-down clearances in the quotation. Automatic separator tension control should not be interpreted as automatic electrode pick-and-place or a fully automatic production line. No production-rate or maximum-layer-count specification is stated for this configuration.

The recommended ambient humidity range describes the equipment environment, not a universal moisture specification for electrode materials. Apply the handling and dryness requirements appropriate to your chemistry.

Stacking vs. Winding

This Z-fold stacker is intended for stacked electrode assemblies, not cylindrical jelly-roll winding. For wound cylindrical or pouch cell cores, compare our motor-assisted manual electrode winding machine. For preparing sheet outlines before stacking, see our semi-automatic electrode die cutting machine. Browse pouch cell preparation equipment for related laboratory tools.

Maintenance and Installation

Use a stable work surface with sufficient support for the approximately 50 kg machine and space for the separator roll and operator access. Keep separator rollers and the stacking table clean, lubricate moving bearing/slide parts as directed and inspect fasteners regularly. Isolate electrical and pneumatic supplies before servicing. Clean and protect the machine surfaces for extended storage.

Request a Quote

Send electrode and tab dimensions, separator specifications, intended layer count and stack thickness, any smaller-size or thicker-stack requirements, your chosen AC 220V/50Hz or AC 110V/60Hz supply, quantity and destination. We will confirm configuration, utilities, included tooling and pricing by email.

View full details

Request a Lab Quote

For institutional purchase orders, non-standard configurations, larger quantities or written shipping terms, send the details below. We will reply before anything is ordered.

Product: Semi-Automatic Z-Fold Electrode Stacking Machine for Pouch Cells
SKU: FL-BDP200-B

Submitting this form does not place an order or confirm availability, pricing or delivery. DDP shipping is included for most destinations we serve. Remote, restricted or unsupported destinations may require different terms, which we will confirm before fulfillment.